Most of the homework has been done for your Block 1 Clone Build
This is the 2017 limited release Colt M4A1 carbine rifle, in semi-automatic. Direct from Colt factory, still in factory wrapping. Nothing added, nothing taken off. In the Summer of 2017, there were roughly 200 Colt LE 6920 SOCOM rifles released. This is quite a collector's item, and the foundation for a "Block 1" clone build.
This is the real deal, complete with all Colt parts and an ambi safety selector, and genuine Knights Armament KAC RAS rail and covers. Four position Colt buffer extension tube and a Colt / P&S Products "waffle" stock. This is a very nicely "finished" Colt carbine. Better than any we have seen. You expect a great quality engineered rifle from Colt, and you get it. But, you normally also expect some handling marks, oil randomly applied, and sometimes a scratch or two. This batch of 2017 rifles are very nicely finished. You will sit back, and say, "wow."
Very Limited Supply. Super Very Limited.
The barrel is a 14.5" heavy SOCOM profile, with a 1.6" factory pinned and welded extended A2 Colt flash hider. Since the barrel is pinned and welded, this is NOT a short-barreled rifle (SBR), not an NFA item, requiring a special tax stamp. This is street legal.
This rifle is fully loaded will all the bells and whistles, and is the 2017 limited release with the old Colt "C" stamp on the upper receiver.
Colt factory M4A1 carbine
14.5" Colt SOCOM barrel, pinned and welded at the factory to 16.1" with an extended A2 flash hider; CAGE rollmarked
Colt M4A1 roll-marked lower receiver -- the real deal, with LE series serial numbers
Colt M4 factory "C" stamped upper receiver
Knights Armament KAC M4 quad RAS rail with three (3) KAC 11-rib covers
Matech 600m back-up rear site from Picitinny Engineering
Colt factory installed front side sling swivel
Colt ambidextrous safety selector
Colt / P&S Products "waffle" stock with P&S CAGE code
Colt "C" marked bolt carrier group with MPC marked bolt
Colt mil-spec charging handle
Colt 4 position buffer / extension tube, with Colt buffer and factory staked castle nut
full Colt (Hartford) factory installed lower parts and Colt A2 grip
Note: This is the from the limited release 2017 rifles, of which there were roughly 200 sold. Do not confuse this with an HBPW or other newer or older releases. The 2017 release had all the bells and whistles, ready for battle.
There will be more SOCOM rifles from Colt, but never another 2017 limited release with the old familiar "C" roll-mark. This is truly a work of art and science. Excellent product, and finely crafted. Better than we have seen with any other production rifle.
ITAR Product By adding to cart, I understand, acknowledge, and agree to the Export Policy. I am a US Person, and I do not intend to export this product.
NOTE: MUST READ FOR FIREARM AND LOWER RECEIVER ORDERS:
THIS IS A SERIALIZED FIREARM. IT MUST SHIP TO AN Federal Firearms License holder. No civilian exceptions.
When you check-out: We no longer take PayPal, as it has caused some confusion on the purchase of firearms, which is contrary to PayPal policies, and we had no way to retrict it just for FFL items.
A firearm cannot be sent directly to you. I am sure you know this, but for the fake-news reading this, who might think that a firearm can be mailed to a buyer, I have to reiterate: A firearm or federal regulated serialized item (like a receiver or suppressor), only a federally licensed firearms dealer may receive such an item. It would be good to know your FFL and their shipping address before purchasing. If you know the FFL address, please put this in your shipping address at check-out. Any deviation from this, and your order could be delayed. Sorry, have to have strict controls here. We have a very manual process to reconcile orders to FFL transfer agents. The easier you make it for us, the less likely your order will be held-up. This is a highly regulated process, and compliance is monitored and enforced by the ATF.
Also your FFL must contact us by email, and send us a scanned copy of their firearms license. We prefer a .pdf copy, and not a .jpg. This is your responsibility to obtain and have emailed to us, or snail mail. We do not have a fax machine. Best practice is for your FFL to note your name and order number in the email header. We will not follow-up with your FFL. They should send to: FFL@charliescustomclones.com . If you forget, you can email us at the return address of any of the order confirmations that you receive.
Note: California residents, click here for CA compliant processing. This will also work for New York residents. We will act on your behalf and instructions to ship to restrictive states, but ultimately, it is your responsibility to know the local and state laws. We are in Virginia, and cannot, and do not know all the nuances of other states. If we ship to your FFL, and there is an issue, we cannot accept a return, so please make sure that you know and follow your local and state laws.
Please note our shipping timelines. We do not ship immediately. Also, if you choose the free 5-7 day shipping, those orders ship after all other forms of shipping chosen. Express shipping is given priority.
Be sure to read our return policy. While your satisfaction is our primary concern, we are limited in a highly regulated business environment by what we can and cannot do, and the number of local, state and federal regulations. We do not accept returns for ammunition and firearms, other than obvious defects. Your gun dealer or transfer agent is responsible for inspection for defects: